How to tie a ponytail with a long wig
There's a ponytail character in every work of art who wears her hair up!
For example
Sword Dance
　Nikkari Aoe
　Taro Tachi
Fgo
　Tomoe Gozen
　Sasaki Kojiro
I don't want to be in pain, so I'd like to swing to defensive strength.
　Sally
I'll die if my guesses go to Budokan
　Eri
I'll die if my guesses go to Budokan!
　Soma Kanzaki
etc. ......
However, there are so many people who are not very good at tying up, and we hear a lot of problems.
Q.
- The surface becomes shaggy and messy
- The netting shows through.
- The part of my hair that is tied up is getting loose.
- I don't want a fake ponytail.
- The look of the valance is not what I imagined.
Can you solve these problems?
A.
We can solve all of them!
The individual steps themselves are simple and easy.
But we will show you how to make a full-fledged tied-up wig.
If you have given up on tying up your hair ......, let's get a beautiful back view from today!
What you need
- Wig
- Combs
- Hair comb and toothbrush (useful if you have one!)
- String elastic
- Dacquard
- Hair spray
The wig used for this project is here: ......
Straight 80cm - Purple 11
https://classewig.com/wig/index.php?main_page=product_info&products_id=8126
Rough procedure
- Secure the wig to the mannequin with a gusset needle
- Block the hair into five sections.
- Tie up the blocked sections in order
- Prepare the surface of the wig
- Finish!
Now, let's get started!
â– Procedure Details
1. fix the wig firmly to the mannequin.
　　Stick the gusset needle into the ◠part as shown in the image.
　　Fix the other side, which is not visible, in the same way.
Caution
　At this time, fasten the collar of the wig as far down as possible!
　If the wig is made to fit the mannequin, it may be too small when worn, or the natural hair may be visible.
　Pulling on a wig that is too small may cause it to fall down!
Adjust the height of the mannequin so that it is easy to tie up.
　　It is easier to work with the mannequin if the whip is positioned at the chest.
3. Using a comb, block the wig into five sections.
　　First, separate the wig into front and back sections.
　　For the front blocking, separate the hair from the whorl to the back as shown in the image.
　　The right side and left side should have the same amount of hair.
4. next, divide the back (1), (2), and (3) into three sections.
　　(1) is from the whip to the level of the temples.
　　(2) is from the end of (1) to the base of the ear.
　　The rest is (3).
(4) is the front left side and (5) is the front right side.
5.
(1)(2)(3) blocking should be done in a loose braid about 15cm apart from the root to prevent tangling at the ends of the hair.â
6. Now, let's tie up the hair.
　　First, tie blocking 1. at the position where you want to tie up the final knot.
　　The position where (1) is tied up will be the standard, so make sure it is in the ideal position.
If you always tie a knot, be sure to pull on the elastic while tying!
In this case, we recommend using a string elastic rather than a silicone elastic, which is less likely to get stuck.
For instructions on how to use the elastic string, check out the image here!
7. divide the hair from blocking (2) into three parts: left, right, and center.
The amount of hair on the left and right sides should be 2 to 3 fingers wide, which is enough.
8. To prevent transparency, start back-blocking from the roots of the hairs on the left and right sides that have just been separated.
This area will eventually be covered by blocking (4) and (5), so it is OK to brush back the hair from the surface.
If you are not good at reverse hairs, try using a comb or toothbrush for reverse hairs!
9. tie up blocking (2) and blocking (1) hairs together.
Don't worry if the surface is a little shaggy.
10. To prevent transparency, reverse the hair from the collar of blocking (3).
Point1: Lifting the hair upwards while brushing back the hair will make the hair flow upwards, making it easier to tie up.
Point 2: The place to reverse the hair is the part that will be on the inside when the hair is tied up (especially at the roots).
If you find it difficult to reverse hair while lifting the hair ......, you can use a hair iron to change the flow of the hair upward and then work with it.
You can also watch the video here for an explanation of how to reverse the hair.
11. tie up the blocking (3) and the hair from (1) and (2) together.
How to tie up the hair is also explained in the video here.
Please refer to it.
12. part the left side blocking (4) in half vertically.
　　Thereafter, the front side. (4)B and the back side (4)A (4)A for the back side.
The right side blocking (5) is likewise divided in half vertically, with the front side as (5)B and the back side as (5)A.
To prevent transparency, brush back the hair from the inside at the circle of blocking (4)A (especially at the root).
　　Do the same for blocking (5)A. 14.
Slightly tuck in the roots and tie the hairs of blocking ( 4)A and blocking (5)A together at the point indicated in 1.
Be careful not to pull the hair straight and tie it up, as this will reveal the natural hair when the wig is worn!
15. use the hair bundles from blocking (4)B andblocking (5)B to make the surface of the wig look nice and neat.
　　With these hair bundles, tie up at the position (1) to hide the inverted hairs.
　　By the way, separate the hair bunches left on the sides in advance!
Finally, spray the hair to harden it and you're done!
Many people have trouble tying up ponytails, but by tying them up little by little, you can actually do it easily and beautifully.
Use this method to get your ideal ponytail!
Other! If you have any questions about the style, color, or processing of your wig
Please feel free to contact our staff at CLASSES!
E-mail: message@classewig.com
