Marble wig Vol.1ï½¥Grade & mesh

　Hello! Sorry for the late update! I was in the middle of editing an article yesterday. I was in the middle of editing an article yesterday when it froze and my data was lost..............orz I have a mixed hair color character. Nowadays, there are more and more mixed-hair-color characters. Using multiple wigs This is an experiment of marble wigs. Sewing the hair bundles together. It is cost-effective and reliable, but In addition to that It's very easy. This is a very easy way to make two colors. Red 05 (R05) was prepared. It is red as it looks, but it is characterized by its matte finish and low gloss. Often, when you do different colored hairstyles. The easiest and most convenient way is to stack two wigs. The wig that covers the head is Silver 02 (S02) desu. The problem with stacking two wigs is It makes my head look a little big...(^-^;) There! To minimize the head enlargement. Cutting the wig with the netting. First, prepare a sharp cutter (with replaced teeth). Please note that if the cutter is not sharp enough, it is easy to get injured (><). Then, turn the wig inside out and keep the whorls facing forward. And sewn round and round The cutter is inserted into the gap between the hair bundles The rest is cut along the flow. Surprisingly, it's easy and clean cut. I wish you the best of luck! So, after almost a full circle, one bundle of hairs will remain. I cut it off and... The cutout is complete! (v´e) Like a sea anemone... (sweat) By the way, the upper side is the forelock part. The net of the forelock part remains 3 cm wide. Be sure to leave at least 1 cm width of netting on the bangs part! Otherwise, it will disassemble...(´-ω-ω;) sweat. It is meaningful to cut out in a circle (^-^) When I asked Yoshiko to put this on her head Kappa hair! Va! I can't go out very much as it is. I'm going to make a plate to put on top of it. Cut it in a larger circle than before. I'm using Silver 02 layered shorts. Use a pen to "mark" the area to be cut. The net width of the bangs to be left is 1.5 cm. Cutters are inserted into the gaps between the hair strands. In the same way, cut along the flow ~. This time it is a large circle, so the hole goes all the way to the back net. The rubber part cannot be cut with a cutter. It needs to be cut with scissors and detached. Once separated, place the plate over the kappa hair. Sew it on from the back to complete the two-color hair *. The size of the head does not change that much in appearance. Now, the rest of the person I just cut out. If you put this on... The plate is bigger than before. To the kappa hair! Then, put regular Black 03 (BK03) Layer Short on top of it. Only the inside of the hair will be a little white (^-^) In addition, if you want to mesh through the gap in the elastic at the back of the net. Pull the white hairs out through the gap in the elastic of the net at the back. More and more meshes like this. Natural mesh can be applied throughout. The same goes for the bangs. I can't pull them out because the net is jammed (>_< .) 　So, first use a cutter to make a cut at the place where you want to pull it out. 　Then, pull it out. Can you see the black wig with the horizontal cut brewed along the flow...? Brush it up. Get the red one ready. When you put it on, it becomes three colors of WW. For the sake of clarity, I've used a combination of harsh colors. If the colors are close, it can be used for gradation. well now The black 03 I mentioned earlier. You can make this one in a kappa shape, too. Yellow Brown 01 (YB01) is applied on top. The headless wig of Nurarihyon's grandson is completed. Cut black bangs. So that you can't see them. I think it would be closer. This time, the theme is an experiment in layering. Marble Wig Part 1 is finished! See you soon. Cosplay General Specialty Store Classe Top