Hairdresser's laboratory 2 Movement bangs, reducing the amount of hair ~Cut demonstration~

it's been awhile (since I last saw you) This is Anmuu m( )m I'd like to introduce Candy Velvet's Taishow, a hair stylist at Candy Velvet. to appear on the show. to teach us how to cut! http://www.candyvelvet.com/ In this issue. How to cut bangs☆.

　This is a review and continuation of the previous bangs cut (patched).

　First, let's start with the bangs cut!

　Cut the part to be cut and the part not to be cut with a clip.

　Make a triangle shape.

　(If it is difficult to understand, please refer to the previous blog.)

Pinch it between your middle and index fingers. Make the cut little by little. (Do not use scissors directly across, but cut vertically (about 45 degrees). Cut to the length you have imagined. If you plan to add layers in advance

　It is better to cut a little longer (5mm to 1cm).

　Then, add layers!

　First, gather the hair between your fingers in the center.

　Lift the hairs so that they are parallel to the ground and the eyebrows.

　The height (angle) of the hair at this point determines the lightness of the bangs.

　Lift at 45 degrees: Slightly lighter.

　Lift at 60 degrees": Lighter.

　Lift 90 degrees" ... Much lighter.

　90 degrees > 60 degrees > 45 degrees > = much lighter > lighter > slightly lighter

　After deciding on the angle, use the scissors not directly horizontally as in the Patzun version, but vertically (about 45 degrees) for 5mm.

　Cut vertically (about 45 degrees) by 5mm to 1cm.

　The bangs are combed a little. We will check the lightness of the hair by looking at it little by little. If it still feels heavy, repeat the above process while increasing the angle. Next, we will look at how to apply a layered cut to the bangs. The next is how to cut bangs when you want to reduce the amount of hair in the bangs.

　Divide the basic triangular shape of the bangs into two parts (top:bottom = 3:7).

　Important point] Make sure to divide the hair into two parts by dividing the upper part into the lower part = 3:7. m( )m

The bangs should be split 3:7 (top: bottom = 3:7). Cut only the bottom part with combing scissors. The hairs on the top part of the separated If the purpose is only to adjust the hair volume, do not cut the hair with carding shears. (Important) If short hairs are poking up to the surface or (>< ) This is because short hairs may stick out on the surface or leave a cut line when you cut with a combing shear. Important point】How to use the carding shears Never cut straight across with carding shears (><) It will leave a clear line like perforations. (Tears) Cut vertically (about 45 degrees) just like cutting scissors. Also, do not cut from the base of the wig with combing scissors. The hairs that have been combed short will stand on end. Root of wig to the tips of the hair. Use a pair of combing scissors to cut from about halfway down. If the same area is cut several times with carding shears, the hair will be lost. Check and cut little by little.

　Gradually comb out the bottom portion.

Let down the top hairs. Freehand fine-tune the hair until you get the bangs you imagined and like. It's done! I'm so proud of it! Therefore, we are pleased to announce that I, Anmuu♀, have explained somewhere before. "Cut the wig from the root with a combing scissors. You are wrong! (**) Sorry! For information on how to cut by all means by all means Please refer to the contents of this page. m ( ) m Also, if you are not good at cutting You can have it cut directly at the store... Please contact us through the following website. VOICE Beauty Salon Candy Velvet （Candy Velvet) http://www.candyvelvet.com/ We have been working with layers who are not satisfied with their cut and set. We provide full support for layers who are not satisfied with their cuts and sets. For inquiries, please contact us at candy_velvetti@yahoo.co.jp at See you soon. Cosplay General Specialty Store Classe Top