Hello everyone.
My name is Aoi, and I am in charge of class styling.
This time, I would like to introduce
"how to add tiers".
"I finished cutting the hair, but...something is wrong!
I can't get the tiers to look natural!
If you can't get the tiers to look natural, this is a must-see!
Let's make your wig look smart!
Let's make your wig look smart!
Okay, I cut it short! But...
What do we do about the non-bobbed characters?
A little more advanced technique this time!
Let's add a step!
But first!
How to cut and adjust the amount
I want to know more details! If you think
How to adjust the amount of hair on a wig
How to prevent "I did it! Basic cutting method to prevent
to prevent "I did it!
Now, we will go on to the explanation of the dan cut.
To cut in tiers,
take the hair of the wig vertically and
and
scissors perpendicularly to the floor.
Cutting the hair vertically means...
It is like that.
Putting the scissors perpendicular to the floor is...
It is like that.
It may be difficult to understand from the image alone, but
But if you actually try it on a wig, you will understand.
Blocking is also important when adding tiers.
Divide the hair into top and bottom two equal sections, or top, middle and bottom three sections.
Cut hair from the lower section.
If you use a dakkar, pin, etc. to fasten the uncut portion
You can work without disturbing the work.
Now, let's return to the explanation of step cutting.
The step cut is a cutting method that changes the "angle" at which the hair is lifted.
The angle at which the hair is lifted changes the way it is stepped.
What? What do you mean?
To answer the question "What does it mean?
We will actually put a step in the wig and explain the procedure!
First, take a section of hair lengthwise.
Then, cut the shortest hair in the center of the head at the hem.
Cut the hair with cutting scissors along your fingers.
The reason for cutting from the tips of the hair in the center of the head is
The reason for cutting from the tip of the hair in the center of the head is so that you can use it as a guide to
cut the entire wig evenly!
With the first cut at the center of the wig
around the wig so that the wig is symmetrical.
Cut the right side and the left side of the wig in a circular motion so that they are symmetrical.
When cutting gradually from the standard area
When you gradually cut the hair from the standard section, hold a little of the hair from the previous section with you.
You will be able to see the hair you cut before through to the back of the head.
It will be easier to know where to cut.
You don't have to get it exactly right.
It is okay if the lengths are not perfectly matched, since they will not be extremely different!
When you cut the first section and proceed to the second section
It is easy to understand if you take a little bit of hair from the first section you cut and use it as a guide.
You can cut without hesitation.
Now, let's take the center part of the cut as a guide.
Using the center of the cut as a guide
Let's cut the neighboring hairs.
Now we have a nice, clean step like this!
By the way, if you want to make the tiers widely up and down
If you want to get a wider section up and down,
pull the hair up diagonally when you take the hair vertically.
As you can see in the lower left photo, the entire temple is covered with a wide step.
If you want to add a modest width to the tier,
pull it down a little.
After pulling it out, cut it with scissors like this.
It may be hard to cut at first, but once you get used to it, it's easy to make tiers.
Once you get used to it, it's easy to make tiers, so give it a try!
If you repeat the above method
the style will be so different!
You can use it in different styles.
Please try the step cut.
Make your wigs look stylish!
Let's make it look cool!
See you again (*'O'*)sh!
Go to General Cosplay Shop Classe Top
