Kill two birds with one stone with Vance processing. Collar wig & hair extension

Hello! It's been a while again (sweat). This time, by popular demand How to reduce the amount of hair in the valance and Increasing the amount of hair on wigs of how to do both at once. wigs at the same time! A valance is just so convenient! Please take a look at the following In using the valance What do you do with a character with a small amount of hair? The valance of the classe is full of hair (especially 40cm...) 80cm and 100cm are also very heavy. In order to firmly support the weight of the hair, the valance clips are also large. （The hair is very heavy, so the 80cm and 100cm hairs are very heavy.) But for a character with a small amount of hair But for a character with little hair, it may be a little too big or too much hair.... But it would be a waste to reduce the amount of hair. But it would be a waste to reduce the number of hairs! To get just the right amount of characterful, just the right amount of hair Here's a quick and easy way to get the most out of your cut! First, prepare the valance. I used it before and had it left on hand. I'll take apart the 80cm valance of Gray 01 (▼▼)χ(▼▼)χ(▼▼)χ(▼▼)χ(▼▼)χ(▼▼)χ) First, disassemble the valance of the classe... Untie the elastic and remove the valance clip. This is what it looks like when opened. It looks... a little bit like an insect (;´´decision´´). Hold the rubber part and the other side of the cut into the other side. Pull the elastic out. The upper elastic in the photo is the one that originally came out. The lower side in the photo is the one that was cut and pulled out. And... JOKI*JOKI* with scissors between the rubber and the rubber... What a surprise! Two Vance! minute (((≧∇≦()≧∇≦))) body The upper side of the photo can be used as a less hairy valance. However, it may get tangled during disassembly. 　Please be very careful when working on it (><) Insert it into a slightly smaller valance clip that you purchased yourself. You can make your own valance by hand. (By the way, the valance clip in the picture was too small. I'm sorry. After tightening the elastic and tying it. Handmade valance is completed. I know I am persistent, but the valance clip in this picture is too small.................... Let's prepare it according to the amount of hair. If you don't have a good hair clip, you can sew it directly to the wig like a bundle of hair. Or you can sew it onto a wire comb sold at 100-yen stores before attaching it. The size of the vance clip will change the "heaping up" of the tail section. Try it out! Well... Here is the other half of the arrangement. First, pull out the elastic. Cut off the excess net part. This time, to make it look like wolf hair. I'm going to use it as a wig for the nape of the neck. Yoshiko is wearing a short, straight gray 01 wig. (The sides and bangs have been cut off.) How to put it on Patch Clip Hand sewing There are two ways to do this. First, it is hand-sewn. In deciding where to sew, you need to choose a position that looks like the orange line, and then sew it on by hand. Sew from the top along the wig's hair bundle in a horizontal line. (The photo is turned inside out for clarity.) Regular hair bundles can also be increased in the same way, at the place where you want to increase the hair. Sewn in one row from the front~. It is a normal wave stitch... (^-^) But even with this, it almost never comes off. (I used white yarn for clarity, but the color of the yarn should match the color of the hair.) By the way, please don't sew too much on the part with the vertical elastic. If you sew over the vertical elastic with thread, the elastic will not be able to stretch in the vertical direction. This can also cause the wig to not fit properly. Dare to sew without vertical elastic ~(ω`b) The next method is to use a patch clip. ← Like this. Patch Clip (tentative name) is scheduled to be released soon φ(Pω^* ) Sew it to the net with a thread and a needle Fasten the wig at the desired location. View from the back A couple of clips are enough. and fit the "row" at the back of the head where you want to fasten it. Fasten the handmade nape wig. Let your hair down and get it ready. It went like this! I'm using 80cm valance, so super long ... This is what it looks like from the side. If you use a 40cm valance or cut it down, it will look like this you can easily create a wolf-like hair. It's easy to do a small hair comb. A valance can be used for a wide range of purposes other than as a valance. Other uses include hot water perming and sewed it to the short straight nape of the neck, and then curled it a little. Cut the excess part of the valance into small pieces. You can also use it for partial extensions. You can also exchange valance parts with your friends (*^-^*) So, we are going to exchange That was the economical Vance Full Use Experimental Repo! See you soon. Cosplay General Specialty Store Classe Top