Hello everyone.
My name is Aoi, and I am in charge of class styling.
This time, on behalf of the moon!
I'd like to introduce you all to a new processing method.
Even if you don't like to tie up your hair
With the twin-tail base, you can do it!
The beautiful parting of the hair, and the collar is also neatly done up.
If you use this wig, you will not be left out of anything.
You can make up your hair prettily! You can do it!
This twin-tail base wig is very popular and is sold by Classe.
This time, using the twin tail base
I would like to arrange it in the popular Sailor Moon style!
Before processing, isn't it easy to get tangled because it's PRO?
If you think...
Clip the ends of your hair when you are not shooting.
Apply plenty of silicone spray!
Try to use it with some ingenuity!
First, let's block the bangs.
The bangs are a triangle tied from the corner of the eye to the top of the head.
After blocking is complete, remove the down part of the hair except for the bangs.
Move the hair out of the way so that it does not get in the way.
If it does not interfere with the cut of the bangs
You can tie or clip the hair if it does not interfere with the cut of the bangs.
Now cut the bangs.
We will part the hair later.
So, let's cut the bangs a little longer.
At this stage, it is okay to leave the hair in a loose bun.
Now we will do the start-up.
First, part the hair in the center and wet it thoroughly.
Use a hair dryer to make sure the shape is firmly in place.
Warm the root of the wig firmly.
Once heated, wait until the residual heat is removed.
or switch the hair dryer to cold air to shape the wig.
Cooling agents can be used to cool down the heat.
If you want to process standing bangs, please refer to this article (Rin Matsuoka article).
Please refer to
this article (Rin Matsuoka article).
Now, once the bangs are parted, curl the ends of the hair.
First, separate the blocking of the bangs into upper and lower sections.
Use a
hair iron to pinch the ends of the hair at the
bottom of the parted section, and straighten the hair by hand.
At this point, depending on the temperature setting
Be careful not to burn yourself!
When the hair is set, adjust the length of the hair.
Use combing scissors to thin the ends of the hair.
Use combing scissors to thin the ends of the hair and make it shorter while making it easier to gather.
The fringe has been thinned and cleaned up toward the ends.
Next, cut the top portion of the hair in half.
Divide vertically into three sections.
The middle part is cut short to
cover the part where the net can be seen through.
Cut the middle part short so that it can cover the part where the net can be seen through.
First, see the figure below.
The hair on the left and right sides will blend in naturally as shown in the image by simply lowering the hair.
After adjusting the ends of the hair with a setting agent, the bangs are completed.
Now let's move on to making the twin-tails.
This time, we will use a twin-tail base.
Twin-tail base can be used for
it is possible to easily tie up a wig that has been untied once.
and you can easily tie it back up!
Even if you are not good at tying up wigs, you can easily tie them back up.
But, if you have a problem with
"I can't tie up my wig because it's out of place!"
"I can't tie it up tight enough with the net pulled on!"
In such cases
Please use our
special mannequins for processing!
The mannequin is equipped with a needle that can be inserted into the mannequin, so that the wig can be fixed to the mannequin.
You can fix the wig to the mannequin by inserting a hook into the mannequin!
Now, let's get back to the original story.
Let's quickly re-tie the wig into high twin-tails.
The key points for re-tieing are as follows
The
round bun should be
tied at the place where you want it to be.
The ends of the hair should be tied back through the elastic to form a bun.
This is the important part that gives the bun its volume!
Next, secure the valance.
In this style, the clips of the valance are in the way.
So, let's remove the clips.
Open the clip of the valance and loosen the tied elastic.
the clip will come off!
This time, the clip will not be used. We will let you do it this time.
Place the unclipped valance over the base of the bun.
Tighten the elastic to secure.
Make sure to tie the end of the elastic tightly.
Once the valance is firmly secured to the base
Tear the hair ends of the valance into two pieces, top and bottom.
Leave the bottom part, which will not be used for the bun.
The point here is that the
top hair will be used for the bun and the bottom hair will be used for the bottom part.
The key point here is
the ratio of the top hair that will be used for the bun and the bottom hair that will be the part that will be left down!
Be careful not to make the bun too big or too small.
Be careful not to make the bun too big or too small.
The top hair should be smaller than the bottom hair, so that the bun is the right size.
Next, tear the ends of the top part in two again.
Wrap the ends of the top part around the base of the bun.
You can wrap the hair around the base of the bun without thinking too hard, because the base of the bun is there.
You can wrap the hair around the base of the bun without thinking too hard.
Dumplings are ready!
Finally, I curled the ends...
It is completed! Holy shit!
You can create the dumplings in different shapes depending on your preference.
Here is a tight dumpling made.
By the way, here is an image with the decoration.
How did everyone like it?
No matter how you tie up your hair or how unnatural your parting is
This wig is the solution!
And because it's a Classe PRO, you can even do a bun with just one bounce!
You can even make a bun with just a single bounce!
If you have any questions about the style, color, or processing of your wig, please feel free to contact us!
Please feel free to contact our staff!
Email: message@classewig.com
We will see you soon!
Back to the top of the cosplay specialty store "Classe
