Hello everyone.
My name is Aoi, and I am in charge of Classé Styling.
We are pleased to announce the release of a new board for modeling from Classe.
The name of the board is "COS Board".
COS Board" has been released by Classe.
For those of you who think that you don't do modeling and have nothing to do with it
You are thinking that you don't do modeling and don't care about it!
Today, I'd like to show you an unexpected use of the COS board.
I'd like to show you an unexpected use of COS board
I would like to introduce an unexpected use of the COS board.
We will use
Straight 45cm A - Pink 05
Vance 40cm - Pink 05 and
Hair bundle 60cm - Pink 05
And
COS board (seal type) M size 1.5mm
First, start with blocking of the foundation.
Tie a knot from the top of the head to the side of the ear, and roughly divide the hair into front and back.
Once parted, tie up the hair at the back.
Tie up the hair so that the tail is on the left when viewed from the front (the photo shows the back, so the tail is on the right).
(The photo shows the back, so the tail is on the right.)
At this point,
leave a little bit of hair at the hem (collar).
If you have long natural hair collar, it is convenient to make a collar to hide your natural hair.
Cut the collar as shown below.
Then, make the sides and bangs.
Separate the sides and bangs into blocks while envisioning the finished look.
Once the hair has been separated as shown in the figure
First, apply heat to the side ends of the hair with an iron
Wrap it around a ballpoint pen and curl it.
The curl will shorten the length of the hair.
Please curl the hair first and then cut.
The hair ends are finished like this.
Next is the front left side of the hairline.
Let's cut it short.
It is also possible to make it stand up without cutting.
In that case, please apply here.
The cut part will be fixed with spray.
To create a hairline, cut in a jagged shape at the desired length.
If you are not good at creating a hairline by sticking a bunch of hair.
You can also express the root of the rising part in this way.
*Please note that this method is inappropriate for all-back hairstyles.
Now let's finish the bangs.
The rightmost part of the front should be swept toward the ear.
When wearing, place over the ears and secure with pins.
Leaving a long section in the center, cut both sides and comb the ends of the hair.
Create a flow of hair on each side and secure with spray.
And here comes the
COS board comes into play The COS board is here.
The long part in the center. To fix the curl at the hair ends
COS board (seal type) M size 1.5mm is used.
The image below is cut for tail processing.
*The actual M size is 600mm (length) x 900mm (width).
First, cut the COS board to the thickness of the hair bundle you want to finish.
Heat is applied to the COS board to form the shape.
Another nice feature of the COS board is that it can remember its shape when it cools down.
Once the shape is made, peel off the sticker and attach the hair bundle.
The hair bundle is heated again, and the shape is attached.
If the adhesion is too loose, use a glue gun or spray to fix the hair bundle firmly in place.
If not, use a glue gun or spray to fix the hair bundle firmly in place.
Stick the finished parts to the bangs.
Use a glue gun for adhesion, and stick it on as if it were submerged in the glue.
Attach the bangs to the surface of the COS board and cover the board with hair.
The bangs and sides are done!
Next, let's finish the back.
Use COS board for the tail section as well.
Cut out the desired width, apply heat, and shape
Paste the hair bundle as before.
The tail part is finished like this.
Then, the valance is disassembled.
For details, please see this article for details.
Inside the valance before attaching it to the small clip
Glue the tail made from the COS board we just used.
I used gouge spray and the heat of a hair dryer to create the shape.
I think it would be easier to use a wire in the COS board...
Tough.....
Here, cut the excess part of the hair ends (tails) of the foundation wig, and
I use a glue gun to make sure the elastic doesn't come loose.
This base holds the valance firmly in place.
The key is to cut off the ends of the hair, as much as you want to!
Finally, bite the tail and you're done!
Sculpting isn't the only use for a COS board!
It is also very useful for creating that character or that character...
Lightweight and easy to prepare!
We hope you will try it out on a variety of wig sets.
This time, we used a bundle of hair.
But if you cut the valance and use the leftover half as a hair bundle
You can make a wig without a hair bundle.
It is also possible to process without hair bundles to reduce costs.
If you have any other questions about the style, color, or processing of your wig, please feel free to contact us.
Please feel free to contact us!
E-mail: message@classewig.com
See you again soon!
Back to the top of the page
